ALUMINUM
~ FITTINGS for Awnings ~ USE:
Application in the construction of Awnings
~ Schedule-40 |
[
CAPS
Eye End ] [
Rafter-TEE ] [
Front/Rafter BAR-Clamps ] [ Head Rod Clamps ]
[
Tie-Down
Clamps ] [
SlipFit Elbows
] [ Camel Back HINGES ] [ Post Sockets ] [ Awning RAIL
and WELT ] [
Cleats ]
Square-Tube-ALUM
Round-Tube-ALUM STAINLESS
TUBING
OD
= Outside
Pipe Diameter;
ID = Inside
Pipe Diameter
[ Prev ] < Awning FITTINGS > [ Next
] |
Aluminum #FBCL-3/4x1 AL; sized
for Schedule-40-Pipe
Rafter Combo FRONT BAR CLAMP (USA Only) Littco
SLIPFIT 3/4 "ID and 1"ID Schedule-40 tubing into the bar clamp and
tighten the stainless steel setscrew, then fit over
the
tubing and lock with the setscrew.
For
Rafter-Piping
1.050" OD
(over 1"OD )
And
Front-Bar-Piping
1.315" OD (over 1-1/4"OD ) |
|

Schedule-40
 
Schedule-40
 |
Alum FRONT BAR CLAMP for
1.050"OD tubing
Littco
for
3/4"ID Schedule-40-Pipe (with 1.050"OD / Outside Diameter)
SLIPFIT 3/4"ID x
3/4"ID tubing into the bar clamp and
tighten the stainless steel setscrew, then fit over
the same size
tubing and lock with the setscrew.
For
Piping 1.050" OD
(over 1"OD ) #AL-2378 |
|
Aluminum FRONT BAR CLAMP for 1.315"OD Tubing
Littco
for 1"ID
Schedule-40-Pipe (with 1.315"OD / Outside Diameter)
SLIPFIT 1"ID
x 1"ID tubing into the bar clamp
and
tighten the stainless steel setscrew, then fit over
the same
size tubing and lock with the set screw.
For Piping 1.315" OD (over 1-1/4"OD )
#AL-2380 |
|
|
Select "ADD To
CART"... Type
QUANTITY & Update
[ Prev ] < Awning FITTINGS > [ Next ] |
Aluminum TIE DOWN CLAMP for
1.315"OD Tubing Littco |
Clamp to tie down pipe to 5/8"od-rods. (and
for 1"ID Schedule-40)
For
Piping 1.315" OD (over 1-1/4"OD ) #TC-78 (j2432)
|
for 5/8" rod plus

1.315"OD/Tubing | |
IMPORTANT
Read Carefully:
AWNING FITTINGS
Are Sized Based On Schedule-40-Pipe's INSIDE-DIAMETER
(With A Larger
Outside-Diameter)... See The Noted ID And OD figures
provided for each fitting,
And Compare To The ACTUAL
MEASUREMENTS On The Pipe Which You Are Using...
If not sure, using the actual OD measure
of the Pipe, compared to the OD figure below,
may be wiser. |
IMPORTANT: READ
Before Ordering
The
measurements for these fittings are based on the pipe sizes of
Schedule 40 Pipe,
which
is measured by the inside diameter of the pipe, not the outside as with
marine fittings.
OD = Outside Pipe Diameter;
ID = Inside Pipe Diameter
FOR EXAMPLE:
1/4"ID Schedule 40 pipe has an outside diameter of 0.540 (OD) inches (over 1/2"OD ),
1/2"ID
Schedule 40 pipe has an outside diameter of 0.840 (OD) inches (over 3/4"OD ).
3/4"ID
Schedule 40 pipe has an outside diameter of 1.05 (OD) inches (over 1"OD ),
1"ID Schedule 40 pipe has an outside diameter of 1.315 (OD) inches (over 1-1/4"OD ).
OD = Outside Pipe Diameter;
ID = Inside Pipe Diameter
[ A
*MINIMUM $30 Order in Product Required
+ S/H costs, On ALL Fittings ordered. ]
*Note: Select Carefully, since All
Sales Are Final...
The aluminum hardware is cast alloys that are best suited
to each applications.
All parts have a smooth surface with a bright
finish.
Set screws, hinge screws, bolts and nuts are of stainless steel
unless otherwise indicated.
Many of the parts appear
similar to their counterparts in the boat top trade, they tend to be larger castings
and in many cases are not as well finished as the
equivalent boat parts.
[ CAPS
Eye End ] [ CAPS
Thread Eye ] [ Bar Clamps ] [ Head Rod Clamps ] [ Tie-Down
Clamps ]
[ SlipFit Elbows ]
[ Camel Back HINGES ] [ Post Sockets ] [ Awning RAIL and WELT ] [ Cleats ]
[ STAINLESS
TUBING ] < TUBING > [ ALUMINUM
TUBING ]
|

NOTE:
AWNING Fittings Are Sized
By The Awning
Schedule-40-Pipe's INSIDE Diameter;
OD
= Outside
Pipe Diameter;
ID = Inside
Pipe Diameter
|
~ Awning Fittings Only ~
Sizing NOTE:
If
You Are Using Other Types of Piping, use that PIPING's Outside-Diameter (OD),
and Compare to the Awning-Fitting's OD Info above, that it would
accommodate...
BACK To CSC INDEX
|
|
A
CS CORP Company, USA
CSC ~ SUPPLY
GROUP

© Copyright CSC 1999-2021 All Rights Reserved
Designated Trademarks and
Brands are the property of their respective owners.
|
|