Hardware ~
ALUMINUM ~ AWNING FITTINGS
USES
- Application in
the construction of Awnings |
[
CAPS
Eye End ] [
Rafter-TEE ] [
Front/Rafter BAR-Clamps ] [ Head Rod Clamps ]
[
Tie-Down
Clamps ] [
SlipFit Elbows
] [ Camel Back HINGES ] [ Post Sockets ] [ Awning RAIL
and WELT ] [
Cleats ]
Square-Tube-ALUM
Round-Tube-ALUM STAINLESS
TUBING
[ Prev ] < Awning FITTINGS ~ MOLDING & Welt > [ NEXT ] |
POST SOCKETS |
Aluminum. POST SOCKET
for 1.050"OD Posts on Wood
Post socket for mounting pipe
into wood surfaces. Littco 205-W
(for Wood/Decks) ... or 205-L (for Lag/Brick/Mortar)
For Piping
1.050" OD (over 1"OD )
#j2422 (3/4"ID-Sched40)
The Actual FITTING ID, Accommodates a Tube with
1.05"OD
|

Select
Wood or Lag |
Select "ADD To
CART"...
Type QUANTITY & Update |
Aluminum
POST SOCKET
for 1.315"OD
Posts on Wood
Post socket for mounting pipe into wood surfaces; for
1"ID Schedule-40-Pipe (1.315"OD)
For
Piping 1.315" OD (over 1-1/4"OD ) #j2424
Littco 206-W (for Wood/Decks)
The Actual FITTING ID, Accommodates a Tube with
1.315"OD
|

Wood |
Aluminum POST SOCKET For 1.315"OD
for Posts on
Brick/Stone
for
1"ID-Schedule-40-Pipe (1.315"OD / Outside Diameter). Littco 206-L
(for Lag/Brick)
Post socket for mounting pipes securely
into brick or stone surfaces. (For
Lag-Screws use)
For
Piping 1.315" OD (over 1-1/4"OD )
#j2425
The Actual FITTING ID, Accommodates a Tube with
1.315"OD
|

Brick / Lag |
|
|
If
you are not sure of sizing, Call before ordering, since All Sales Are
Final... Thanks |
[ Prev ] < Awning FITTINGS ~ MOLDING & Welt > [ NEXT ]
[ STAINLESS
TUBING ] < TUBING > [ ALUMINUM
TUBING ]
|
IMPORTANT
Read Carefully:
AWNING FITTINGS
Are Sized Based On Schedule-40-Pipe's INSIDE-DIAMETER
(With A Larger
Outside-Diameter)... See The Noted ID And OD figures
provided for each fitting,
And Compare To The ACTUAL
MEASUREMENTS On The Pipe Which You Are Using...
If not sure, using the actual OD measure
of the Pipe, compared to the OD figure below,
may be wiser. |
IMPORTANT: READ
Before Ordering
The
measurements for these fittings are based on the pipe sizes of
Schedule 40 Pipe,
which
is measured by the inside diameter of the pipe, not the outside as with
marine fittings.
FOR EXAMPLE:
1/4"ID Schedule 40 pipe has an outside diameter of 0.540 (OD) inches (over 1/2"OD ),
1/2"ID
Schedule 40 pipe has an outside diameter of 0.840 (OD) inches (over 3/4"OD ).
3/4"ID
Schedule 40 pipe has an outside diameter of 1.05 (OD) inches (over 1"OD ),
1"ID Schedule 40 pipe has an outside diameter of 1.315 (OD) inches (over 1-1/4"OD ).
OD = Outside Pipe Diameter;
ID = Inside Pipe Diameter
[ A
*MINIMUM $30 Order in Product Required
+ S/H costs, On ALL Fittings ordered. ]
OD
= Outside Pipe Diameter;
ID = Inside Pipe Diameter
*Note: Select Carefully,
since All Sales Are Final...
The
aluminum hardware is cast alloys that are best suited to each
applications.
All parts have a smooth surface with a bright
finish. Set screws, hinge screws,
bolts and nuts are of
stainless steel unless otherwise indicated.
Littco.
Many of the parts appear similar to
their counterparts in the boat top trade,
they tend to be larger
castings and in many cases are not as well finished
as the
equivalent boat parts.
[ STAINLESS
TUBING ] < TUBING > [ ALUMINUM
TUBING ]
|
BACK To CSC INDEX
|

Sizing NOTE:
If
You Are Using Other Types of Tubing, use that PIPING's Outside-Diameter (OD),
and Compare to the Awning-Fitting's OD Info above, that it would
accommodate...
< FASTENERS &
FITTINGS
>
[ DOT-DURABLE ] [ LIFT-The-DOT & Tools ] [ PULL-The-DOT ]
[ Dot-Durable DIE Tools ] [ MOLDING CLIPS ] [ GROMMETS ]
[ Top VENTS ~ POLES ] [ QUICK-FIT Kits ] [ Bimini FRAMES ]
MARINE / BOAT FITTINGS:
[
NYLON
] [
STAINLESS
] [
CHROME
] [
TOOLS
]
AWNING FITTINGS
(Aluminum) :
[ CAPS
Eye End ] [ CAPS
Thread Eye ] [ Bar Clamps ] [ Head Rod Clamps ] [ Tie-Down
Clamps ]
[ SlipFit Elbows ] [
Camel Back HINGES ] [
Post Sockets ] [
Awning RAIL and WELT ] [
Cleats ]
Alpha Awning Frame
Parts
[
Clip / Side-Release
BUCKLES ]
[ STAINLESS
TUBING ] < TUBING > [ ALUMINUM
TUBING ]

|
|
|
A
CS CORP Company, USA
CSC ~ SUPPLY
GROUP

© Copyright CSC 1999-2021 All Rights Reserved
Designated Trademarks and
Brands are the property of their respective owners.
|